Showing posts with label tool building. Show all posts
Showing posts with label tool building. Show all posts

Monday, February 20, 2012

Disasters and discoveries in the alloy aisle, plus a new furnace


So, given my somewhat less-than-satisfactory results with the aluminium bronze, I started looking into other options. I looked at buying pre-alloyed aluminium bronze, but shipping will bite me. My next thought was Za-12, a zinc/aluminium alloy with excellent castability and hardness (google it).

While at a scrap yard looking for the piece of steel that makes up the front leg of my new furnace (read on for more), I discovered that the man who owns the scrapyard also sells ingots of zinc, 5kg each. AU50c/kg! At that rate, I'll be going with za-12, I hear it's easy to make at home given the low melting point of zinc.

Now, on to the furnace...


While 'making' the aluminium bronze, I overheated my furnace, driving the Portland cement reaction backwards, and making my refractory more like 'refractury'. A short while later, I found an abandoned water heater, one of the little ones. I also found a stock trolley in a skip. After putting my thinking cap on, I decided to build a completely new furnace, rather than relining the existing one.

I cut the water heater down, cut a ring out of it for a lid, and welded it onto the trolley, about 20cm above ground level. Then I welded a piece of 40mm box section steel -- the one that the nice guy at the scrapyard gave me -- onto the front, to provide support for the weight of the furnace.



The recipe for the refractory that I picked cannot be found here, because something has gone wrong with my link. Instead, I will just list the ingredients.

40% bentonite
25% 200-mesh silica sand
20% fire clay
10% alumina
5% borax


It has no cement in it, so is essentially a ceramic reaction, which I won't be able to drive backwards, no matter how hard I try. Hopefully.

I haven't done the lid yet, because I ran of of clay... But I won't be able to cast again for a while anyway, so that's fine.

[EDIT] I made the clay too wet, so it cracked and buckled all over the place. As a result, I had to let it dry and powder it right back down. Given how little extra volume I actually need for the lid, I've decided to add stuff to the mix willy-nilly to make up the volume. I have some perlite, which will go in, and I'll put in some sawdust as well, which will burn out, leaving a stronger, honeycomb-like structure. I might add some more clay and sand too, depending on how I'm feeling. More news later.

Tuesday, January 24, 2012

A new project: ambitious, but possible

OK, I have a new major project. I'm going to build myself a Gingery-inspired lathe. If you don't know who Gingery is, google him. In short, he was a man who needed a machine shop, but lacked the funds for one. He had plenty of time though, so he decided to build one. He made many machines out of cast aluminium, which he melted in a furnace in his back yard. I admire his ingenuity, but feel that his lathe design is somewhat lacking in some areas. Those areas are:

size - his lathe is very small
fittings - his lathe has no standard tooling fittings
engineering - there are numerous engineering points that I disagree with, I'll cover these as they appear though


So, the first part that needs doing is the bed and ways. (Engineering flaw #1) Gingery cast his bed out of aluminium, making a 60cm hollow ribbed block for rigidity. Being aluminium, though, it is not particularly rigid. I imagine this lightweight casting introducing many inaccuracies, mostly through flexing and sagging. The other major downside to the bed is that it's a very big casting, especially for novices, at whom the series is mostly targeted.


To counter both of these problems, I have decided to skip casting the bed, and opt instead for a steel I-beam. This should give me the extra weight and rigidity that I yearn for, while also allowing me to scale the whole lathe up a bit (this addresses flaw #1, size). I plan on scaling it up to a 75mm swing, with around 60cm between centres.



Here is my basic idea for the bed: The black I-shaped section is, strangely enough, the I-beam. The thin grey piece is an aluminium match plate that I will cast up, and the red is a piece of bright flat bar.

The purpose of the match plate is simple. I will first scrape one side of it to fit the I-beam perfectly, then I will scrape the other side to match the bright bar perfectly. This will mean that the inaccuracies on the surface of the I-beam won't matter, as they will be averaged out by the aluminium plate. Then, given the very close tolerance of the bright flat bar, the matched aluminium surface will be almost perfectly flat. This will mean that I can bolt the bright bar onto it and not have to worry about it deforming.


Now, the only problem I can see with using I-beam is that it is not designed to withstand torsional force, which is exactly what I will be putting on it. I have two thoughts on this:
1) it may be so grossly over sized that it doesn't matter
2) I could weld straps into it, between the two parallel surfaces, and perpendicular to them. This would change the side view from being a long, wide channel, to a series of boxes. I feel that this should strengthen it sufficiently against the torsional forces.

So, those are my current plans. I'll update you as I build. But for now, google Gingery and see what he's all about.