Showing posts with label ingots. Show all posts
Showing posts with label ingots. Show all posts

Monday, February 20, 2012

Disasters and discoveries in the alloy aisle, plus a new furnace


So, given my somewhat less-than-satisfactory results with the aluminium bronze, I started looking into other options. I looked at buying pre-alloyed aluminium bronze, but shipping will bite me. My next thought was Za-12, a zinc/aluminium alloy with excellent castability and hardness (google it).

While at a scrap yard looking for the piece of steel that makes up the front leg of my new furnace (read on for more), I discovered that the man who owns the scrapyard also sells ingots of zinc, 5kg each. AU50c/kg! At that rate, I'll be going with za-12, I hear it's easy to make at home given the low melting point of zinc.

Now, on to the furnace...


While 'making' the aluminium bronze, I overheated my furnace, driving the Portland cement reaction backwards, and making my refractory more like 'refractury'. A short while later, I found an abandoned water heater, one of the little ones. I also found a stock trolley in a skip. After putting my thinking cap on, I decided to build a completely new furnace, rather than relining the existing one.

I cut the water heater down, cut a ring out of it for a lid, and welded it onto the trolley, about 20cm above ground level. Then I welded a piece of 40mm box section steel -- the one that the nice guy at the scrapyard gave me -- onto the front, to provide support for the weight of the furnace.



The recipe for the refractory that I picked cannot be found here, because something has gone wrong with my link. Instead, I will just list the ingredients.

40% bentonite
25% 200-mesh silica sand
20% fire clay
10% alumina
5% borax


It has no cement in it, so is essentially a ceramic reaction, which I won't be able to drive backwards, no matter how hard I try. Hopefully.

I haven't done the lid yet, because I ran of of clay... But I won't be able to cast again for a while anyway, so that's fine.

[EDIT] I made the clay too wet, so it cracked and buckled all over the place. As a result, I had to let it dry and powder it right back down. Given how little extra volume I actually need for the lid, I've decided to add stuff to the mix willy-nilly to make up the volume. I have some perlite, which will go in, and I'll put in some sawdust as well, which will burn out, leaving a stronger, honeycomb-like structure. I might add some more clay and sand too, depending on how I'm feeling. More news later.

Sunday, January 29, 2012

Experiments with aluminium bronze

Today I made some aluminium bronze, and it was a partial success I think.
I learnt a few things about the material, but I'm sure there's more to learn.

The first thing that I learnt is that it takes a surprisingly long time to melt copper; I was still trying after 20 minutes at full blast. Its melting point is 1084.62 degrees celsius, but either I couldn't get that hot, or there's some trick to melting copper. I got it to a very bright red-heat, but it wouldn't go any further.

So here's the lesson in that: according to The Complete Handbook of Sand Casting by C.W. Ammen, you should melt the copper first (p189), then add the other metals. I got fed up with w

aiting for the copper to melt, so I added my aluminium, which began to melt almost instantly, forming a puddle in the bottom of the crucible. Once this puddle had formed, the copper began to melt really quickly. If anyone can explain this, please do. Anyway, in future, I'll put copper in the bottom, aluminium on top, then more copper, then fire it up.
The second thing I learnt is that either aluminiun bronze is not nearly as golden as the internet would have me believe, or that it's a lot harder to get the ratios right than I thought. I aimed for 10% aluminium by weight, so I put 9 parts copper and 1 part aluminium in (2kg copper, 222g aluminium). One thing that leads me to believe that the ratio is hard to get right is that there was an awful lot of dross (or something that looked like dross) stuck in the bottom of the crucible after the pour. Thus, much of either or both metal oxidized. At what ratio, I can't say, but surely it is likely to skew my intended ratio.

In all honesty, I don't care about the colour, and the colour came out being pretty nice anyway. It looks almost like steel, only shinier. What I care about is the mechanical properties.



Here's an idea of the colour: the watch is stainless steel, the light has made everything a little yellower, though there are some patches about the place on other ingots that actually are that yellow. Also, notice how smooth the side is, and the two big flat bits on the top. The bumpy bits were loose bits of sand. This implies that I can get a pretty good finish with this alloy even with reasonably coarse sand.





The third thing I learnt is that aluminium bronze needs to cool slowly, otherwise it becomes very brittle. I quenched most of the ingots that I cast, with the result that I could break them by hand, or by dropping them from a height of about a metre. This had me worried, until I found an ingot I had forgotten to quench. I couldn't break it at all, I didn't try with a hammer though. In future, NO QUENCHING.

Here is a n ingot that I quenched, it was so brittle that I could snap it in my hand. It leaves a very sharp edge, I discovered the hard way. Notice how shiny the inside is? Also, you can see how it's quite crystalline. This has to be the result of the quenching, as the alloy ratio is almost certainly similar to the range of 'real' aluminium bronze, and I have one ingot, which wasn't quenched, which isn't brittle.